Shear Bending Tool Series

Used for installing pipelines and repairing in factories, warehouses, docks, buildings, railways, automobiles, etc.

The YAX-DWG Model Electric Hydraulic Pipe Bender is a state-of-the-art electrohydraulic pipe bending machine that offers a wide range of capabilities. With its reasonable structure and convenient operation, this machine ensures safe and fast loading and unloading, making it a valuable addition to any workspace. Whether you need to install new pipes or repair existing ones, this pipe bender is the perfect solution for your needs.

Function: Suitable for general water pipes, conduit, thick steel pipes, etc., with an angle of 90 degrees bending

Applicable to industries such as pipeline maintenance, pipeline construction, testing, flange replacement, gaskets maintenance, pressure vessels, bearing disassembly and jacking work.

Features：
-Lightweight, economic and pleasant design, easy to use.
-Adjustable tip width from 70-216mm, with a wide range of applications.
-Single acting, spring retractable, RC series hydraulic cylinders facilitate quick and trouble-free operation.

-For maintenance, commissioning,shutdowns, testing and valves change. 
-No need for hammers, chisels, slings or chain block Integrated wedge concept.
-Friction-free, smooth and parallel wedge movement eliminates flange damage and risk of spreading arm failure.
-Unique interlocking wedge design-no first step bending and risk of out of joint.
-Requires very small access gap of only 6 mm FSM-14 is available as bolting tool-pump set for your ordering with spreader, hand pump, hose, gauge and adaptor.

Suitable for pipeline maintenance, repair, testing, and flange replacement applications, with no friction, parallel, smooth movement, and will not cause flange damage.
The wedge size ：6mm
There are two options: mechanical and hydraulic.

This product is suitable for wiring engineering of automatic control panels in switch boxes and distribution boards. It adopts a separate type and is easy to carry;
The center point of the copper aluminum bar must be aligned with the center position of the piston in order to cut it. After cutting, the cut should be flat and not deformed;
This machine is a specialized tool for cutting off copper and aluminum busbars, without dust or noise;
The cutting blade is made of alloy steel and undergoes heat treatment. The fracture surface is smooth and neat, without deformation or burrs. The cutting speed is fast, and the surface is stable without the need for further straightening;

1. Suitable for indoor and outdoor engineering of power transmission and distribution rooms, various connection fittings, and professional use of overhead underground cables.
2. 10kV-500kV high-voltage cable sleeves, wire clamps, bare terminals, hexagonal crimping, tight and not easily detached, with good conductivity.
3. Adopting a split type, the working environment requirements are reduced, and the self weight is light. Manual pump, foot pump, or electric pump are required for operation.
4. Oil pipe joint with PT3/8 "thread.
5. 13 sets of molds.

Instructions for using hydraulic cable cutters
1. Choose appropriate cables (cable size less than 50mm)
2. Close the oil return switch tightly, then pull the movable handle to start the plunger pump, causing the oil pressure to rise. The large piston pushes the blade into operation until the cable is cut off.
3. After completing the work, loosen the oil return switch, wait for the piston to stabilize, then close the oil return switch tightly, and then switch for the second time.
4. Remarks: The split type needs to be equipped with a pump for use

Performance characteristics
The combination busbar processing machine produced by our factory is a comprehensive busbar processing center that integrates cutting, punching, flat bending, and vertical bending. Widely applicable for copper and aluminum processing in power supply bureaus, substations, power plants, and the vast power industry for installing power lines.
Cutting capacity: copper and aluminum bars 120mm x 10mm
Punching capacity: Copper and aluminum with a thickness of 10 mm and an air diameter of 10.5-20.5 mm
Flat bending and force bending capacity: 120*10mm
Weight: 140kg
Input voltage: 220V/380V

Using oil as the working medium, motion is transmitted through changes in sealing volume, and power is transmitted through the pressure inside the oil.
Our factory mainly produces a series of products including rechargeable hydraulic pliers, hydraulic pliers (integral and split type), hydraulic shears (hydraulic and manual), hydraulic hole openers, vertical bending machines, busbar processing machines (hydraulic punching machines, hydraulic bending machines, hydraulic cutting machines, hydraulic embossing machines), angle steel cutting tools, vertical bending machines, hydraulic pullers, hydraulic pipe bending machines, hydraulic jacks, manual pumps, electric pumps, pressure testing pumps, hydraulic steel bar shears (hydraulic and charging), ratchet scissors, peelers, cable pulleys, etc.

-Split -unit hydraulic hole digger is specialized for corner steel, flat steel, brass plate and other metal material's hole digging.
-Especially for electric power building and other industry's field operation.

-The hydraulic hole opener is suitable for finished products with distribution boards, switch boxes, and sheet metal that have been baked and painted as a whole.
-It can temporarily change the specifications and easily change the mold size. 
-After perforation, it will not damage the surface.